59 Inches RGB Multi-Color Dynamic Scanning Starter Hood Lights, Car LED Hood Light Strip, Exterior Flexible Headlight Waterproof Daytime Running Lamps Strips (1 Set)

great looking when you start it up
this is the second one i buy, after 3 months half of the lights would not light up, but i liked it so much im trying it again. its great at night ,not only does it look nice but it helps light up the road in front of you. hope this one last a long time, I thought I had submitted this review when I bought it in January, I came back on here to let you know this is my second one I bought and this time it lasted 6 months , as much as I like the look of it and the light it gives off at night . I will not be buying another one ☹️

Low Voltage reset value
Liked the turn signal option after I had a different white only version (different seller) and thought it was going out so ordered this one. Checked to see if there was any issues pre-install and nothing so installed and 16hrs later last 4 inches of light were out. Contacted seller they said they were aware and it was a manufacture problem they had addressed with them and offered to send replacement. Got second one and no issue with pre-install tests. Have not been able to do reinstall due to recent arm injury so can’t say how long second one will last.Now to the others and a quirk I noticed. 1) this control box is not 100% waterproof. 2) power wires from controller to lights and leads for turn signal inputs are 24-26 gauge (very small). 3 Low Voltage reset value. My ‘18 Ram has a control fuse for all external lights so I installed the power line next to headlights receptacle so it would turn on/off with lights and not be on 24/7 draining battery. Thought it was working fine until I was following a friend and they said that it was constantly ‘scanning’ white light. So started diagnosing issue and found that a .5 voltage drop would cause it to recycle its chip to say it had just received power on signal. That is a very ridiculously low voltage difference for that IMO. So if you’re an owner of a newer car and not electrical savvy might not work out as planned and need to be installed by someone.Now to the quirk. With all that said I disconnected power so that it wouldn’t cycle but yellow lights still work when unlocking car but not for turn signals. Weird right. Will update when I have new installed or figure out voltage issue.

Very Rugged construction/100% Water Resistant
After measuring & establishment of the center of the LED Hood light strip i made sure to clean the complete area & even farther in both directions where the lights were going to be secured with the double sided adhesive strip under the hood with 90% Isopropyl Alcohol to insure there was no contaminate on the surface where it was going to be attached & also used one of my heat guns to pre heat the area as well as the adhesive backing strips before & during fastening it to the top of the grill & across the plastic cover/Shield that cover’s the grill/radiator etc… & also attached a 1″ wide strip of double edge 3M brand adhesive over the top of the adhesive strip that’s attached to the light strip from the manufacturer & made sure to heat it with my heat gun for complete adhesion to the grill & left the Red adhesive covering on the top to keep it from sticking to the underside of the hood & i’ve ran it through the carwash several times & it hasn’t moved At All & works Flawlessly !! I HIGHLY Reccomend it for anyone who wants their vehicle to “Stand Out” from the crowd or could use a little extra lighting because even during the Brightest part of the day it’s still Very Visible !!

Works ok
Installed this on my SUV. It was easy enough to install once I figured out how to use a fuse splitter. The adhesive that came on it was ok, but I used some 3M automotive gasket adhesive to keep it in place so it wouldn’t come off during a car wash or anything. One thing I’ll mention is, if you decide to trip the light strip, be aware it will stop working a few inches before the spot you cut it. So if it’s 60 inches, and you need to trip it down to say 50 and cut it at 50 inches, it will stop working around 47 or 48 inches. So trim in small increments. Also, because of the startup animation, if you trim it, the animation will not be in sync. It’s hard to explain and I didn’t capture it on film. Basically, right out the box, the light turns on from each side, meets in the middle, then bounces back. If you trim it, it still does it, but doesn’t account for where you trim it. So the distances will be off.

Worst product low quality

Exelente