Adam’s Polishes Advanced Graphene Ceramic Spray Coating – 18+ Months Sprayable Graphene Oxide Ceramic Coating for Cars, Boats, RV’s & Motorcycle | Adds Extreme Gloss, Depth, Shine & Protection

Great product!!!
Wow, just wow. I honestly figured I was being played like always, by another wax/ car shine product. This stuff is amazing. Easy to use, goes a long ways and works. I have a black 2024 truck. It’s still looking nice, but didn’t have that new pop, like it did when I bought it. I have Adam’s a try and as of now, 3 weeks and 3 washes later, maybe truck looks like it did the day I bought it. The paint may peel off here in a few months ( time will tell), but for now, this is my go to stuff.

Review after 1 Year – A Really Good Coating with an Unbeatable Value
A few important notes: Complete surface preparation was done prior to application. Polished with Menzerna P085rd to remove the previous coating (Gyeon Pure Evo). Used Gyeon Prep to remove any remnant polishing oils and to leave a bare paint surface. The 1st coat was applied on 09/05/24. I applied a 2nd coat on 10/12/24. I wash the car every 2 weeks using P&S Frostbite (traditional bucket wash) or P&S Absolute (rinseless). I use Meguiar’s Hybrid Ceramic Detailer as a drying aid. This detailer does add a small, immaterial amount of protection but it’s gone/removed by the next wash.Application and removal were easy but it can be tricky depending on your weather. I used a small (2″x4″) dense foam block wrapped with a microsuede cloth. I sprayed 3 times directly to the applicator and wiped in a cross-hatch pattern for even coverage on one panel (door, fender, half a roof, half a hood, etc). In my warm Texas autumn weather, the product would rainbow on the surface almost immediately. I waited an additional ~10 seconds before removal. One plush towel to level high-spots, a second plush towel to remove the majority of product, and a third low-nap towel for finishing and buffing to a shine. I did a test spot on my roof where I followed Adam’s instructional video (apply, see the rainbow effect, wait for the rainbow to fade, then remove). It was *impossible* to remove the coating as it had completely set. I blame the hotter-than-normal Texas temps for this. I highly recommend doing a test spot to find the optimal timing of removal for your climate.Appearance-wise, the coating has a very glossy, liquid look. But to be honest, pretty much every coating is going to look the same/similar when the paint is perfect. Slickness was a notable standout as the surface was smooth to touch and towels glided without any degree of grabbiness.Durability of protection and hydrophobics are the primary reason to use a ceramic coating. Beads were super-tight and water repulsion was instant for the first 6 months. Then I noticed that small parts of horizontal surfaces (trunk, roof, hood) had transitioned to very fast-sheeting. I did a decon wash in the spring but that did not improve performance. Over the next 6 months, other sections of the car would gradually transition to fast-sheeting. Which brings the timeline to today (11/15/25). At this point, all horizontal surfaces and the lower half of most panels are slow-sheeting (but not pooling) while the rest are fast-sheeting. I took off one star for my rating as I highly doubt that I would have any appreciable durability after 18-24 months (as claimed).After 1 year (13 months to be exact), I would give this coating a rating of 4 stars. It won’t last the 18-24 months claims but most coatings don’t meet their durability claims either unless they are parked in a garage and never driven. It’s easy to apply/remove and it’s a fantastic value when you consider how much product you get (12 oz. vs 30ml/50ml). Next weekend, I am going to repeat the whole routine again as this coating has proven itself.

I have used this many times on my car over the last 3 years and it works well extending the time needed between washes a lot and at wash time the car cleans easier too.

Great overall…